#7 blades are great for an all-over summer cut on the body of the animal, especially on mixed and wire coated breeds. Blades that have an F in their number, like the 7F model, cut the same length but result in a smoother finish and are usually used on thinner, softer hair or to add a finishing touch to recent shearing.
F or FC stand for the same thing: fine cut or finish cut. One brand might call their blade an F and another might say FC but they are referring to the same thing. The teeth on an FC blade are all the same length, so result in a smoother finish than the same blade in skip tooth (ST).
7F = 1/8" 5 or 7 = Skip tooth blades are a rougher cut meant to go through matted tangled hair etc. F stands for Finishing cut smoother cut. you typically would rough cut with a skip tooth and then go over with an F blade. The number stands for the length it leaves the hair.
Keep in mind, when it comes to pet grooming clipper blade size; the higher the number of the blade, the shorter and finer the cut. The blade number will determine the type of cut you get.
The Andis #7FC UltraEdge Detachable Blade is made from carbon-infused steel to offer a harder cutting surface that stays sharper for longer. This quality universal replacement blade will fit any Andis, Oster or Wahl clipper with a snap-on blade mechanism. Leaves hair 1/8" (3.2mm) long.
There is no difference between 7F and 7FC. 7F is the old name of the blade where 'F' stands for "Finish" and 7FC is the new name of the same blade where 'FC' stands for "Finish Cut".
Blades differ in both size and material, with each blade given a number indicating the length of cut. Larger numbers trim hair shorter than lower numbers, with a #7 blade leaving about 1/8” of length. #7 blades are great for an all-over summer cut on the body of the animal, especially on mixed and wire coated breeds.
7F Dog Clipper Blade (3.2 mm) – Groomsaber.
Never use a different size blade than the one recommended for your saw; it's unsafe and inefficient. The revolutions per minute (RPM) won't be accurate, and it's unlikely to cut as well as it should. Teeth: While the blade is important, the teeth do the actual cutting. Blades are described by number and material.
The #7F Ultimate Full Medium Coarse Competition Series Blade features a 3.8mm cutting length.
When it comes to dog grooming at home, we have to be sure that we're giving our furry friends the best care possible. It may seem like a sensible idea to save money and groom your pup at home using your hair clippers, but it's NOT recommended to use human clippers on a dog.
Dog Clipper 10 Blade
This blade trims to approximately 1/16” of hair, making it ideal for close, hygienic grooming and specific detailing. Key Features of #10 Blades: Close Cuts: Perfect for short summer haircuts and trimming sensitive areas like ears, under legs, and around the tail.
Standard blade sizes work in reverse to what you might think. A #30 blade is a lot shorter than a #3 blade for example. The higher the number, the shorter the coat will be. To take the guesswork out, each blade (and comb attachment), tells you what length it will leave the coat (usually given in mm's).
Over time, the blades can become dull, leading to less efficient and subpar results. However, with the right tools and techniques, you can sharpen your clipper and trimmer blades and restore their cutting prowess. In this blog, we will guide you through the process of sharpening these blades effectively.
The bigger the blade, the deeper and wider its maximum cut. Typically, a 10-inch miter saw will cut a 2 x 6 at 90 degrees and a 2 x 4 at 45 degrees; a 12-inch miter saw will cut a 2 x 8 at 90 degrees and a 2 x 6 at 45 degrees.
7F Blade for Finishing: Provides a smoother finish on soft or thin coats. Perfect for Summer Cuts: Excellent for keeping dogs comfortable during warmer months.
For instance, a #7 clipper blade leaves approximately 1/8" hair when going against the grain, but will leave approximately 1/4" when going with the grain.
What's the difference between a #7 blade and a #7FC blade? The Andis size #7 is a skip tooth blade, and the Andis size #7FC is a finish cut blade.
However, as a general rule of thumb, it is recommended to replace clipper blades every 6 to 12 months.
Skip tooth blades work great when cutting through a thick, wiry, or matted coat. The teeth' shape makes going through these types of coats much more manageable and smoother. Skip teeth also offer an advantage when clipping a breed that is supposed to have a wire texture because it leaves the coat looking more natural.